Follow Up Drilling Underway at Altair
Released
Released
Announcement PDF
9 November 2023
FOLLOW-UP DRILLING UNDERWAY
AT ALTAIR LITHIUM PROJECT, USA
Drilling targets eastern extensions of lithium-mineralised claystone
Key Highlights
•
Drilling campaign underway with two remaining
permitted drill sites to be drilled at Altair
•
Drilling is targeting extensions of the mineralised
Siebert formation claystone east of the successful
intersection in hole AL01
•
Drill-hole AL01, completed in Q3, intersected two thick
zones of lithium mineralised claystone, including:
•
33.5m (110ft) @ 481ppm Li from 80.8m3
•
33.5m (110ft) @ 508ppm Li from 147.8m to end-of-hole3
•
Planned holes AL03 and AL02 will test over 7km of strike
potential for lithium mineralisation
•
Assay results for drilling expected in the current quarter
Astute Metals NL (ASX: ASE) (“ASE”, “Astute” or “the Company”) is pleased to advise that follow-up drilling
has commenced at its highly prospective 100%-owned Altair Lithium Project in Nevada, USA.
The follow-up drilling campaign is designed to build on the success of the Company’s first hole at the
project, completed in July, which successfully intersected two broad zones of lithium mineralisation. Two
remaining permitted holes will be drilled to test for lithium mineralization over a 7km strike to the east.
Astute Executive Chairman, Tony Leibowitz, said:
“We are excited to re-commence drilling in Nevada as our lithium growth strategy in North America
continues to advance. The wide intercepts of prospective lithium claystone rocks intersected in the
first hole at Altair marked a key breakthrough for the project. Two holes will now be drilled to test for
extensions of this mineralization over a 7km strike length. If we are successful, this will add significant
scale and upside to the opportunity at Altair.”
Background
Centred south-west of the township of Tonopah, in the heart of one of the world’s most active lithium
exploration districts, the Altair Project was strategically staked proximal to outcropping tertiary
sedimentary host rock (known locally as the Siebert formation) that is known to host claystone lithium
deposits around Nevada. Such deposits include the 15.8Mt LCE (lithium carbonate equivalent) Tonopah
Flats deposit1 and the 9.79Mt LCE TLC Lithium Project2 (Figure 3).
The Company completed the first hole at Altair in Q3 2023, with drill-hole AL01 successfully intersecting
two zones of lithium mineralisation:
•
•
33.5m @ 481ppm Li from 80.8m (265ft), and
33.5m @ 508ppm Li from 147.8m (485ft) to End-of-Hole (181.4m/595ft)
Suite 6, Level 5, 189 Kent St, Sydney NSW 2000 | GPO Box 2733, Sydney NSW 2001
+61 (0) 2 8046 2799 | admin@astutemetals.com
www.astutemetals.com
Figure 1. Drill rig set up at site AL02.
Planned Drilling
Drilling has re-commenced at Altair with planned hole AL02 utilising a higher-powered Reverse
Circulation (RC) drill rig which has been optimized for the drilling conditions encountered previously at
the project. Two permitted holes remain at Altair, which will be drilled as part of the current campaign.
The objective of drilling is to test for the presence of lithium-bearing claystone over a strike extent of
approximately 7km (Figures 1 and 2). If successful, the Company will permit additional holes to be drilled
in the next field season to further establish the extent and grade of lithium mineralisation at Altair.
Figure 2. East-west cross-section showing AL01, lithium geochemistry and remaining planned holes.
Suite 6, Level 5, 189 Kent St, Sydney NSW 2000 | GPO Box 2733, Sydney NSW 2001
+61 (0) 2 8046 2799 | admin@astutemetals.com
www.astutemetals.com
Next Steps
The drilling campaign is expected to be completed by mid-November. Samples collected from AL02 and
AL03 will be dispatched to ALS Laboratories in Reno for analysis, with results expected before the end of
the calendar year.
Figure 3. Altair Project drill-hole location plan
Plan/Hole ID
Easting
Northing
Depth
Status
AL01
470859
4189179
181.4m (595ft)
Drilled July 2023
AL02
478236
4188869
500
Planned
AL03
472767
4189133
500
Planned
Table 1. Drill site locations
Suite 6, Level 5, 189 Kent St, Sydney NSW 2000 | GPO Box 2733, Sydney NSW 2001
+61 (0) 2 8046 2799 | admin@astutemetals.com
www.astutemetals.com
Figure 5. Location of Polaris and Altair Projects, lithium deposits and exploration projects.
1 OTCMKTS: ABML 26 February 2023 ‘Technical Report Summary For The Tonopah Flats Lithium Project, Esmeralda..’
2 TSX.V: LI 17 March 2023 ‘Tonopah Lithium Claims project NI 43-101 technical report – Preliminary Economic Assessment’
3 ASX: ASE 23 August 2023 ‘Broad lithium hits in first Altair drillhole’
Authorisation
This announcement has been authorised for release by the Board of Astute.
More Information
Matt Healy
General Manager – Exploration
mhealy@astutemetals.com
+61 (0) 431 683 952
Nicholas Read
Media & Investor Relations
nicholas@readcorporate.com.au
+61 (0) 419 929 046
Suite 6, Level 5, 189 Kent St, Sydney NSW 2000 | GPO Box 2733, Sydney NSW 2001
+61 (0) 2 8046 2799 | admin@astutemetals.com
www.astutemetals.com
Competent Persons
The information in this report that relates to Sampling Techniques and Data (Section 1) is based on
information compiled by Mr Matthew Healy, a Competent Person who is a Member of The Australasian
Institute of Mining and Metallurgy (AusIMM Member number 303597). Mr Healy is a full-time employee
of Astute Metals NL and is eligible to participate in a Loan Funded Share incentive plan of the Company.
Mr Healy has sufficient experience that is relevant to the style of mineralisation and type of deposit under
consideration and to the activity being undertaken to qualify as a Competent Person as defined in the
2012 Edition of the ‘Australasian Code for Reporting of Exploration Results, Mineral Resources and Ore
Reserves’. Mr Healy consents to the inclusion in the report of the matters based on his information in the
form and context in which it appears.
The information in this report that relates to Reporting of Exploration Results (Section 2) is based on
information compiled by Mr Richard Newport, principal partner of Richard Newport & Associates –
Consultant Geoscientists. Mr Newport is a member of the Australian Institute of Geoscientists and has
sufficient experience which is relevant to the style of mineralisation and type of deposit under
consideration and to the activity which he is undertaking to qualify as a Competent Person under the
2012 Edition of the ’Australasian Code for Reporting of Exploration Results, Mineral Resources and Ore
Reserves‘. Mr. Newport consents to the inclusion in this announcement of the matters based on his
information in the form and context in which it appears.
Suite 6, Level 5, 189 Kent St, Sydney NSW 2000 | GPO Box 2733, Sydney NSW 2001
+61 (0) 2 8046 2799 | admin@astutemetals.com
www.astutemetals.com
APPENDIX 1 - JORC Code, 2012 Edition – Table 1
Section 1 - Sampling Techniques and Data
Criteria
JORC Code explanation
Commentary
Sampling
techniques
Nature and quality of sampling (eg cut
channels, random chips, or specific
specialisedindustry standard measurement
tools appropriate to the minerals under
investigation, such as down hole gamma
sondes, or handheldXRF instruments, etc).
These examples should not be taken as
limiting the broad meaning of sampling.
4¾” reverse circulation (AL01) drilling was
undertaken for drill sample collection.
Samples were collected on a 5-foot basis in
calico bags.
Include reference to measures taken to
ensuresample representivity and the
appropriate calibration of any
measurement tools or systems used.
Aspects of the determination of
mineralisation that are Material to the
Public Report.
In cases where ‘industry standard’ work has
been done this would be relatively simple
(eg ‘reverse circulation drilling was used to
obtain 1 m samples from which 3 kg was
pulverised to produce a 30 g charge for fire
assay’). In other cases more explanation
may be required, suchas where there is
coarse gold that has inherentsampling
problems. Unusual commodities or
mineralisation types (eg submarine
nodules) may warrant disclosure of
detailed information.
Nominal small drill sample was collected for chip
tray and sandwich-sized ziplock bags, with all
remaining sample collected in calico bag for
despatch to external laboratory
Samples were air dried on elevated grid mesh
until practical to transport
Claystone hosted lithium deposits are thought to
form as a result of the weathering of
lithium-bearing volcanic glass within
tertiary-aged tuffaceous lacustrine sediments of
the mapped Ts3 unit. Inputs of lithium from
geothermal sources have also been proposed.
Drilling
techniques
Drill type (eg core, reverse circulation, openholehammer, rotary air blast, auger, Bangka,
sonic, etc) and details (eg core diameter,
triple or standard tube, depth of diamond tails,
face-sampling bit or other type, whether core
isoriented and if so, by what method, etc).
4¾” reverse circulation (AL01) drilling methods
employed. Water was injected to assist with
transport ofsample from bit to surface, as
required.
Drill sample
recovery
Method of recording and assessing core
andchip sample recoveries and results
assessed.
Sample recovery established by dry sample
weights undertaken by independent
laboratory prior to sample preparation and
analysis
Measures taken to maximise sample
recoveryand ensure representative nature
of the samples.
Whether a relationship exists between
sample recovery and grade and whether
sample bias may have occurred due to
preferential loss/gainof fine/coarse material.
Logging
Whether core and chip samples have
been geologically and geotechnically
logged to alevel of detail to support
appropriate MineralResource estimation,
mining studies and metallurgical studies.
Whether logging is qualitative or
quantitative innature. Core (or costean,
channel, etc) photography.
The total length and percentage of the
relevantintersections logged.
Challenging ground conditions arising from the
drilling of quaternary alluvial and soft claystones
did result in poor recovery in some instances.
Instances of poor recovery are not expected
tomaterially impact interpretation of results
Drill cuttings for entire hole logged for lithology by
contract geologist and company geologists
Logging is qualitative
Photography of material intersections of
claystone taken of relevant chip trays
See Appendix 2 for preliminary lithology
logging
Suite 6, Level 5, 189 Kent St, Sydney NSW 2000 | GPO Box 2733, Sydney NSW 2001
+61 (0) 2 8046 2799 | admin@astutemetals.com
www.astutemetals.com
Criteria
JORC Code explanation
Commentary
Subsampling
techniques
and sample
preparation
If core, whether cut or sawn and whether
quarter, half or all core taken.
Full samples (i.e. samples were not split) were
submitted to ALS Laboratories in Reno for
preparation and analysis.
If non-core, whether riffled, tube sampled,
rotarysplit, etc and whether sampled wet or
dry.
For all sample types, the nature, quality
and appropriateness of the sample
preparationtechnique.
Quality control procedures adopted for all
sub-sampling stages to maximise
representivityof samples.
Measures taken to ensure that the sampling
isrepresentative of the in situ material
collected,including for instance results for
field duplicate/second-half sampling.
Quality of
assay data
and
laboratory
tests
Whether sample sizes are appropriate to
thegrain size of the material being sampled.
The nature, quality and appropriateness of
the assaying and laboratory procedures
used and whether the technique is
considered partial ortotal.
For geophysical tools, spectrometers,
handheldXRF instruments, etc, the
parameters used in determining the analysis
including instrument make and model,
reading times, calibrations factors applied
and their derivation, etc.
Nature of quality control procedures
adopted (eg standards, blanks, duplicates,
external laboratory checks) and whether
acceptable levels of accuracy (ie lack of
bias) and precisionhave been established.
Verification
of sampling
and
assaying
Assay quality was monitored using pulp blanks,
as well as certified reference materials (CRMs)
at a range of lithium grades. Pulp blank results
indicated no material contamination of
samples from sample preparation or during the
analytical process. CRM results were within 3
standard deviations of certified values. No
systematic bias nor other accuracy related
issues were identified.
The verification of significant intersections by
either independent or alternative company
personnel.
Sample intervals to be assigned a unique
sample identification number prior to sample
despatch
The use of twinned holes.
Lithium-mineralised claystone Certified
Reference Materials (standards), pulp
blanks and coarse blanks to be inserted into
the sample stream at regular intervals to
monitor lab accuracy and potential
contamination during sample prep and
analytical processes
Documentation of primary data, data
entryprocedures, data verification, data
storage (physical and electronic)
protocols.
Discuss any adjustment to assay data.
Location of
data points
Samples were analysed by method ME-MS41
which is an ICP-MS method employing an
aqua-regia digest. Aqua-regia is not
considered a ‘total’ digest for many elements
however is considered fit for purpose for lithium
and has been used extensively by other parties
exploring for lithium claystone deposits in the
USA.
Accuracy and quality of surveys used to
locatedrill holes (collar and down-hole
surveys), trenches, mine workings and other
locations used in Mineral Resource
estimation.
Specification of the grid system used.
Drill collar locations determined using handheld GPS with location reported in NAD83 UTM
Zone 11. Expected hole location accuracy of +/10m
No downhole surveys conducted on vertical
holes
Quality and adequacy of topographic
control.
Suite 6, Level 5, 189 Kent St, Sydney NSW 2000 | GPO Box 2733, Sydney NSW 2001
+61 (0) 2 8046 2799 | admin@astutemetals.com
www.astutemetals.com
APPENDIX 1 - JORC Code, 2012 Edition – Table 1
Criteria
JORC Code explanation
Commentary
Data
spacing
and
distribution
Data spacing for reporting of Exploration Results.
Drill spacing is appropriate for early exploration
purposes
Whether the data spacing and distribution is
sufficient to establish the degree of geological
and grade continuity appropriate for the
MineralResource and Ore Reserve estimation
procedure(s) and classifications applied.
5-foot sample interval widely adopted as
standard practice in air drilling in the USA.
Whether sample compositing has been applied.
Orientation
of data in
relation to
geological
structure
Whether the orientation of sampling achieves
unbiased sampling of possible structures and
the extent to which this is known, considering the
deposit type.
Claystone beds are regionally sub-horizontal
withshallow dip of <5° although locally this may
vary
Sample
security
The measures taken to ensure sample security.
Samples delivered from the drill site to Freight
agent by Company staff/contractors for
delivery to external laboratory
Audits or
reviews
The results of any audits or reviews of
samplingtechniques and data.
Not applicable
If the relationship between the drilling
orientation and the orientation of key
mineralised structures is considered to have
introduced a sampling bias, this should be
assessed and reported if material.
Suite 6, Level 5, 189 Kent St, Sydney NSW 2000 | GPO Box 2733, Sydney NSW 2001
+61 (0) 2 8046 2799 | admin@astutemetals.com
www.astutemetals.com
APPENDIX 1 - JORC Code, 2012 Edition – Table 1
Section 2 - Reporting of Exploration Results
Criteria
JORC Code explanation
Commentary
Mineral
tenement
and land
tenure status
Type, reference name/number, location and
ownership including agreements or material
issues with third parties such as joint ventures,
partnerships, overriding royalties, native title
interests, historical sites, wilderness or national
park and environmental settings.
Polaris and Altair Claims held in 100% Astute
subsidiary Needles Holdings Inc.
The security of the tenure held at the time of
reporting along with any known impediments to
obtaining a licence to operate in the area.
Exploration
done by
other parties
Acknowledgment and appraisal of exploration
byother parties.
Geology
Deposit type, geological setting and style of
mineralisation.
Claims located on Federal (BLM) Land
Drilling conducted on claims certified by the
Bureau of Land Management (BLM)
No known lithium exploration conducted on
Polaris or Altair areas.
Exploration conducted in the region by other
explorers referenced in announcement body
text
The principal target deposit style is claystone
hosted lithium mineralisation. Claystone hosted
lithium deposits are thought to form as a result of
the weathering of lithium-bearing volcanic glass
within tertiary-aged tuffaceous lacustrine
sediments of the mapped Ts3 unit.
Lacustrine environments formed as a result of
extensional tectonic regime that produced ‘basin
and range’ topography observed across the
stateof Nevada. Inputs of lithium from
geothermal sources have also been proposed.
Drill hole
Information
A summary of all information material to the
understanding of the exploration results
including a tabulation of the following
information for all Material drill holes:
◦ easting and northing of the drill hole collar
◦ elevation or RL (Reduced Level – elevation
above sea level in metres) of the drill hole
collar
◦ dip and azimuth of the hole
◦ down hole length and interception depth
◦ hole length.
Drillhole locations and drilled depths are
tabulated in body report
All holes drilled vertically
If the exclusion of this information is justified on
the basis that the information is not Material and
this exclusion does not detract from the
understanding of the report, the Competent
Person should clearly explain why this is the case.
Data
aggregation
methods
In reporting Exploration Results, weighting
averaging techniques, maximum and/or
minimum grade truncations (eg cutting of high
grades) and cut-off grades are usually Material
and should be stated.
Intersections, where quoted are weighted by
length.
Where aggregate intercepts incorporate short
lengths of high grade results and longer lengths
of low grade results, the procedure used for such
aggregation should be stated and some
typical examples of such aggregations should
be shownin detail.
No cut-off has been employed where the full
intersection of prospective lithology (i.e. Siebert
formation).
The assumptions used for any reporting of metal
equivalent values should be clearly stated.
A 300ppm Li cut-off was used to quote headline
intersections, with allowance for 5ft of internal
dilution by lower grade material.
Spot grades also quoted for single drill sample
intervals
Sample assays from overlying alluvium were
excluded from all quoted intersections.
Suite 6, Level 5, 189 Kent St, Sydney NSW 2000 | GPO Box 2733, Sydney NSW 2001
+61 (0) 2 8046 2799 | admin@astutemetals.com
www.astutemetals.com
Section 2 Reporting of Exploration Results
Criteria
JORC Code explanation
Commentary
Relationship
between
mineralisation
widths and
intercept
lengths
These relationships are particularly important in
the reporting of Exploration Results.
Insufficient information available due to early
exploration status
If the geometry of the mineralisation with respect
to the drill hole angle is known, its nature should
be reported.
If it is not known and only the down hole lengths
are reported, there should be a clear statement
to this effect (eg ‘down hole length, true width not
known’).
Diagrams
Appropriate maps and sections (with scales)
andtabulations of intercepts should be included
for any significant discovery being reported
These should include, but not be limited to a plan
view of drill hole collar locations and
appropriate sectional views.
Included in ASX announcement
Balanced
reporting
Where comprehensive reporting of all Exploration
Results is not practicable, representative
reporting of both low and high grades and/or
widths should be practiced to avoid misleading
reporting of Exploration Results.
This release describes all relevant information
Other
substantive
exploration
data
Other exploration data, if meaningful and
material, should be reported including (but not
limited to): geological observations;
geophysicalsurvey results; geochemical survey
results; bulk samples – size and method of
treatment; metallurgical test results; bulk
density, groundwater, geotechnical and rock
characteristics; potential deleterious or
contaminating substances.
This release describes all relevant information
Further work
The nature and scale of planned further work
(egtests for lateral extensions or depth extensions
orlarge-scale step-out drilling).
Drill results arising from the current campaign will
dictate further work at the Altair project
Diagrams clearly highlighting the areas of
possible extensions, including the main
geological interpretations and future drilling
areas, provided this information is not
commercially sensitive.
Suite 6, Level 5, 189 Kent St, Sydney NSW 2000 | GPO Box 2733, Sydney NSW 2001
+61 (0) 2 8046 2799 | admin@astutemetals.com
www.astutemetals.com
APPENDIX 2 – Polaris Aircore Drilling
Preliminary Lithology Logging
Hole ID From
To
Rock Formation
Lithology
Comments
AL01
0
235
Unconsolidated
Alluvium
Pebbly, rounded to angular and polymictic
AL01
235
275
Siebert
Clayey Gravel
Variable light orange-brown clay content
AL01
275
335
Siebert
Claystone
Tan claystone with minor gravel
AL01
335
350
Siebert
Claystone
Light olive brown claystone
AL01
350
370
Siebert
Claystone
Bluey green claystone
AL01
370
385
Siebert
Clayey Gravel
AL01
385
395
Siebert
Claystone
AL01
395
405
Siebert
Clayey Gravel
AL01
405
445
Siebert
Claystone
AL01
445
475
Siebert
Clayey Gravel
AL01
475
490
Siebert
Claystone
Bluey green claystone with minor gravel
AL01
490
500
Siebert
Claystone
Bluey green claystone
AL01
500
535
Siebert
Claystone
Bluey green claystone with minor gravel
AL01
535
585
Siebert
Claystone
Light bluey green claystone
AL01
585
595
Siebert
Claystone
Dark grey green claystone
Bluey green claystone in part
Bluey green claystone with gravel
Bluey green claystone in part
Bluey green claystone with gravel
Bluey green claystone in part
Suite 6, Level 5, 189 Kent St, Sydney NSW 2000 | GPO Box 2733, Sydney NSW 2001
+61 (0) 2 8046 2799 | admin@astutemetals.com
www.astutemetals.com
APPENDIX 3 – Drill Sample Assays
Sample ID
Hole ID
From (ft)
700593
700594
700595
700596
700597
700598
700599
700600
700601
700602
700603
700604
700605
700606
700607
700608
700609
700610
700611
700612
700614
700615
700616
700617
700618
700619
700620
700621
700622
700623
700624
700625
700626
700627
700628
700629
700630
700631
700632
700633
700635
700636
700637
700638
AL01
AL01
AL01
AL01
AL01
AL01
AL01
AL01
AL01
AL01
AL01
AL01
AL01
AL01
AL01
AL01
AL01
AL01
AL01
AL01
AL01
AL01
AL01
AL01
AL01
AL01
AL01
AL01
AL01
AL01
AL01
AL01
AL01
AL01
AL01
AL01
AL01
AL01
AL01
AL01
AL01
AL01
AL01
AL01
200
205
210
215
220
225
230
235
240
245
250
255
260
265
270
275
280
285
290
295
300
305
310
315
320
325
330
335
340
345
350
355
360
365
370
375
380
385
390
395
400
405
410
415
To (ft)
205
210
215
220
225
230
235
240
245
250
255
260
265
270
275
280
285
290
295
300
305
310
315
320
325
330
335
340
345
350
355
360
365
370
375
380
385
390
395
400
405
410
415
420
Li (ppm)
88.2
98
132
100.5
128
143.5
180
140.5
225
224
259
215
294
327
367
413
490
394
454
567
637
553
430
471
368
428
416
394
439
490
480
594
732
676
455
218
135.5
257
157.5
176
128
256
224
279
Suite 6, Level 5, 189 Kent St, Sydney NSW 2000 | GPO Box 2733, Sydney NSW 2001
+61 (0) 2 8046 2799 | admin@astutemetals.com
www.astutemetals.com
APPENDIX 3 – Drill Sample Assays
Continued
Sample ID
Hole ID
From (ft)
700639
700640
700641
700642
700643
700644
700645
700646
700647
700648
700649
700650
700651
700652
700653
700654
700656
700657
700658
700659
700660
700661
700662
700663
700664
700665
700666
700667
700668
700669
700670
700671
700672
700673
700674
AL01
AL01
AL01
AL01
AL01
AL01
AL01
AL01
AL01
AL01
AL01
AL01
AL01
AL01
AL01
AL01
AL01
AL01
AL01
AL01
AL01
AL01
AL01
AL01
AL01
AL01
AL01
AL01
AL01
AL01
AL01
AL01
AL01
AL01
AL01
420
425
430
435
440
445
450
455
460
465
470
475
480
485
490
495
500
505
510
515
520
525
530
535
540
545
550
555
560
565
570
575
580
585
590
To (ft)
425
430
435
440
445
450
455
460
465
470
475
480
485
490
495
500
505
510
515
520
525
530
535
540
545
550
555
560
565
570
575
580
585
590
595
Li (ppm)
316
293
330
110.5
290
635
154.5
245
124
92.7
67.6
203
208
521
472
579
471
424
564
450
611
597
516
501
408
440
486
688
615
490
646
397
124.5
595
585
Suite 6, Level 5, 189 Kent St, Sydney NSW 2000 | GPO Box 2733, Sydney NSW 2001
+61 (0) 2 8046 2799 | admin@astutemetals.com
www.astutemetals.com
Share your feedback
Discover